Yard measuring guide
How to measure your yard for sod and fence
To measure a yard for sod, split the lawn into rectangles and triangles, multiply to get square feet, subtract the house, paths and beds, and add 5 to 10 percent for cuts and waste. For a fence you only need the perimeter in feet, minus gate openings.
By Eutopix Labs P.S.A. · · AreaWalk is on the App Store
Measure the yard for sod
Sod, seed and turf are sold by area, usually priced and sized in square feet, so you need the lawn area only, not the whole lot.
- Sketch the lawn. Draw the lawn shape on paper and mark everything that is not grass: house, patio, driveway, paths, planting beds, trees you will not be sodding around.
- Break it into simple shapes. Rectangles (length × width) and triangles (half of base × height). Measure each with a tape or a measuring wheel.
- Add the shapes for the whole yard, then subtract the non-grass areas.
- Add waste. A common rule of thumb is to order 5 to 10 percent extra for edges, curves and cuts; more for very curved shapes.
- Check your supplier. Coverage per roll, slab or pallet varies, so divide your total by the coverage the supplier states.
| Item | Area (ft²) |
|---|---|
| Whole lot, 60 × 40 | 2,400 |
| House, 30 × 20 | −600 |
| Driveway, 10 × 20 | −200 |
| Planting beds | −150 |
| Lawn | 1,450 |
| Plus 10% waste | about 1,595 |
The same area works for grass seed or turf. If the seed bag states a coverage in square feet, divide your lawn area by that figure.
Measure the yard for a fence
A fence is priced by length, so you need the perimeter of the line the fence will follow, not the area.
- Decide where the fence will sit and mark the corners with stakes or flags. Allow for any setback or boundary rule in your area, which you should check with your local authority.
- Measure each straight run between corners, and add them up.
- Subtract gate openings, which are priced separately, and count the gates.
- Divide by the panel width to count panels. With 8 ft panels, a 50 ft × 30 ft backyard enclosed on all four sides has 160 ft of perimeter; minus one 4 ft gate that is 156 ft, which is 19.5, so plan for 20 panels.
- Count corner, end and gate posts separately, since the number of posts is one more than the panels on a straight run, and corners and gates need special posts.
Fence length along sloping ground is longer than the flat map distance, so add a little if your yard is steep.
The phone shortcut
A tape works, but a yard with curves, a bed and a diagonal fence line is much easier to measure by tapping around it on a satellite map. Zoom in until the edges of the lawn and fence line are clear, tap each corner, and read the area and the side lengths. For a fence, a distance measurement along the fence line gives the length directly.
AreaWalk handles both on iPhone: the Area tool for lawn square feet and the Distance tool for fence lines, with a precision crosshair that places a point exactly at the screen centre and deep zoom for small yards. Results show in ft², sq yd, m², acres and more, and you can save a measurement with a name and notes. Measuring and reading results is free (three saves); PDF export is a Pro feature. Satellite maps can be a few metres off, so for tight fits, confirm with a tape before you order. About AreaWalk (on the App Store).
Quick checks before you order
- Do the numbers pass a sanity check? A 60 × 40 ft lot is 2,400 ft², and your lawn must be smaller than that.
- Square feet to square yards: divide by 9. Our acres to hectares and square feet chart covers the other conversions.
- For big lawns, the lot may be best measured in acres. See how many acres is my property.
Frequently asked questions
How much extra sod should I order?
A common rule of thumb is 5 to 10 percent extra for cuts and waste, more for yards with many curves. Check your supplier for their advice.
How do I measure an oddly shaped lawn?
Split it into rectangles and triangles, work out each area in square feet and add them, or tap the outline on a satellite map and read the area.
How do I calculate fence length?
Measure each straight run along the fence line and add them, subtract gate openings, then divide by your panel width to count panels.
How many square feet is a square yard?
One square yard is 9 square feet.
More guides
Estimates only. AreaWalk is a measuring aid, not a legal survey. Questions? support@areawalk.app.